Valve Cover Gasket – Lycoming TO-360, TIO/LTIO-540, TIO-541-E Series, TIGO-541-E Series

VALVE COVER GASKET – SILICONE

for  

LYCOMING TO-360, TIO-540 and more

(see complete list below)

•  8 BOLT HOLE GASKET

 

–   Our silicone rubber gaskets are made from aerospace mechanical

     grade AMS  silicone and designed to withstand temperatures up to

     400 degrees Fahrenheit.   

–   Therefore, they will not break down and deform or crack up like

     cork or neoprene.   

–  Our gaskets seal uneven and warped surfaces and 

     eliminate corrosion.

–  Gaskets are 100% reusable.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

 

FAA-PMA approved for the engines listed below.

Fits:       LYCOMING

              TO-360-CIA6D, – FIA6D

              TIO / LTIO-540-V2AD

              TIO-540-AJ1A

              TIO-540-W2A

              TIO-541-E SERIES

              TIGO-541-E SERIES

 

Part #:    RG-76036

Corresponding part #’s:     Lycoming 76036,  06B28890

8 bolt hole silicone gasket

Gaskets sold individually

Silicone gasket is 1/8″ thick

Reusable.

 

INSTALLATION & MAINTENANCE INSTRUCTIONS

1.       All surfaces must be clean and dry, no lubrication of any type

                – Use threadlock (Loctite) in the screw holes. 

2.       Install gasket and CROSS TIGHTEN to value listed:

                           COLD ENGINE    –        25 INCH POUNDS

                           WARM ENGINE   –        20 INCH POUNDS

3.       Perform engine run and check for leaks.
4.       If there is a leak, DO NOT CONTINUE TO TIGHTEN  –  This will only   

        make the leak worse.

–  Remove the gasket and examine its condition.  

               –  If it is still serviceable, wash it briefly in hot water and soap, rinse well,

    dry and reinstall. 

5.       To reuse the gasket, clean as described in # (4) above.   

               –  The gasket surfaces must be clean and dry. 

 

Keep these instruction for future reference

   

CAUTION – DO NOT OVER-TIGHTEN!

Over tightening makes the gasket bulge or squeeze out.

 

Instructions  –  Click  to print 

 

TO REUSE GASKET: 

1.    Wash gasket briefly in hot soapy water. 
2.    Rinse well and dry all surfaces thoroughly. 
3.    Re-install gasket using the above instructions.

 

PROUDLY MADE IN THE USA.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

 

USE CORK?  GET REAL!   REAL Gaskets that is…

 

REAL Gaskets Tennessee is a manufacturer of silicone rubber gaskets 

for aircraft, automobile, and motorcycle engines.

 

Our silicone rubber gaskets are made from aerospace mechanical 

grade AMS silicone, designed to withstand temperatures up 

to 400 degrees Fahrenheit and to last the life of the engine.

 

Our gaskets seal uneven surfaces, eliminate corrosion and 

are 100% reusable.

 

We manufacture valve cover gaskets for:

 

Aircraft: Continental, Franklin, Lycoming, Pratt & Whitney and

Wright radial piston aircraft engines.

 

Automobiles: Ford, GM, Mopar, Porsche and VW automobile

engines.

 

Motorcycles:  BMW, Harley-Davidson, Suzuki, BSA, Ducati,

Moto Guzzi, Norton, Triumph, Saab and most other 

motorcycle engines. 

 

If you are tired of oil leaks, then a silicone rubber gasket is

the only way to go, and REAL Gaskets Tennessee is the

only place you can get “The Original” silicone rubber

gasket.

 

MADE IN THE USA.